Internet of Things: LoRa Hello World

Another LoRa transceiver module finally arrived from China today, now I have two of the things I decided to crack on with building a LoRa push button using an Arduino Uno and the LoRa module. Eventually this will be developed into a small circuit on strip board consisting of the LoRa module, an ATMega328-PU and a DHT22 to make my first LoRa powered temperature and humidity sensor to replace the ESP8266 based sensors I have today.

First steps as per all the other LoRa modules was to solder on some cables with appropriate headers at the other end, for this purpose I used a ribbon of male to male dupont style cables and chopped the connectors off one end, tinned the wires and soldered them to the VCC, GND, MISO, MOSI, NSS, SCK, RESET, DIO0 and DIO1 pads of the module. This module is a unbranded SX1276 module I found on eBay which is more cost effective than the RFM95W which was used for the single channel gateway, the downside is it has smaller pads than the RFM95W so soldering is a little more tricky, but with practice and a fine tip soldering iron you can acheive an acceptable result. Here is a chance for you to laugh at my soldering again...

Next I hooked the module up to an Arduino Uno as per the following pins… You shouldn’t really do this because the logic pins of the Uno are 5v and could damage the module, but I gathered for a quick test it would be ok, and if I fried it they are cheap enough. When mounting this permanently on a DHT22 sensor board I will use some voltage dividers to bring the 5v ATMega328-PU logic down to 3.3v for the module.

SX1276 Pins Arduino Uno Pins
VCC 3.3V
SCK 13
NSS 10
DIO0 2
DIO1 3

Next I plugged the Uno in to my laptop and launched the Arduino IDE. The intention is to send the packets to The Things Network via my single channel gateway, hence we need to find a LoRaWAN library. The most common appears to be the IBM LMIC Framework, go to Sketch -> Include Library -> Manage Libraries to download LMIC to your Arduino IDE.

Once the library is installed open the IBM LMIC Framework TTN example from File -> Examples, don’t upload it to your board yet, there are a few mods we need to make before we upload the sketch to the board. Open up your browser and visit, if you do not have an account already sign up. Once in the console go to the Applications tab and create a new application. Once you have made an application go to the devices tab of the application and register a new device, as over the air activation is not available for these sorts of modules via a single channel gateway just fill out the form with dummy data and click register.

Once you get to the device information page shown above click on Settings to begin the device personalisation. On the settings page change device activation method from OAA to ABP and click save, the page will refresh and the device’s address, network and application keys will be generated for you. Copy these into your sketch in MSB format, you can get the keys in MSB format by clicking the ‘<>’ button next to their text box. You should end up with something that looks like this…

Scroll down the code a bit further until you get to the pin mapping comment. Modify the NSS pin to 10, RST pin to 9 and DIO pins to 2 as per below.

Next keep scrolling until you find the channel setup statements, comment out all the channels other than the channel served by your single channel gateway, in my case all channels except for 868.1mhz. If you are in range of a full 8 channel gateway you can skip this step.

Now you are ready to upload the sketch to the board, once it boots up it should transmit a packet saying “Hello, world!” once every 60 seconds, however the LMIC library does observe duty cycle limitations, so it may be delayed as appropriate. Before you hit the upload sketch button open TheThingsNetwork console, go to your application and select the device you created and open the data tab. Now upload your sketch, providing you are in range of a TheThingsNetwork LoRaWAN gateway you should see packets arriving in the console, if you do not see packets arriving as expected you can use the Arduino IDE serial monitor to look for debug messages from the Arduino, you’ll need to connect with a baudrate of 115200. Once you see the packets in your TheThingsNetwork console you know everything is working as expected, you can now expand the functionality to initiate the do_send function upon some other trigger rather than the timed callback set on line 105, e.g. a button press.

You can expand each packet to show meta data about the packet, for example which gateway forwarded it and the signal strength. The payload is presented as hex, but if you convert it back to ascii then the original contents of mydata in the Arduino sketch can be read:

echo "48656C6C6F2C20776F726C6421" | xxd -r -p
Hello, world!

Great all seems to be working just fine, next I will move on to combining this with periodic polling of data from a DHT22 and moving the circuit to veroboard with a ATMega328-PU standalone rather than having the bulk of the Uno. I may also do some range test to see how far away I can position a sensor, however as my area has a lot of buildings and not many hills I think the range will be quite small compared to some of the many kilometer range tests we see on YouTube for LoRa. Stay tuned for updates.

By @Robert Putt in
Tags : #internet, #iot, #electronics, #technology,